Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFast, Reliable Gate Installation Across Compton
Gate installation in Compton usually means working with what’s already there: a 1960s tract house, a concrete block perimeter wall, and a driveway slab that’s seen fifty or sixty years of tree roots and soil movement. That’s the reality we work with every week in the 90220, 90221, and 90222 ZIP codes. We’re Ironworks Gate Co., and we’ve been hanging and automating Gate Repair in Compton gates for over 42 years, since 1984. If you’re calling from Compton, a live person answers at (747) 774-7784 and we’ll schedule a free measure and written price. Most consultations in Compton happen within a few days, not weeks.
Why Ironworks Gate Co. Is Compton’s Preferred Gate Installation Company
Compton homeowners call us because we don’t fight the existing conditions, we plan for them. The homes here were built between 1945 and 1970, and the concrete work around those houses has been moving for decades. A gate company that treats every job like new construction will bolt a post into a cracked footing and leave. We won’t. Our crews know the streets around Rosecrans Avenue, Wilmington Avenue, and Alameda Street, and we know what those driveways do when a mature ficus or elm tree decides to heave the slab. That’s why our quotes for Gate Installation in Compton always account for what’s under the surface, not just what shows above it.
Every job is protected by the 90-Day Done Right Promise. It’s written, it’s simple, and if something isn’t right we come back and fix it. No paperwork, no arguing. Victor Salinas runs our crews, and the standard he sets is the same one we’ve held for four decades: background-checked, uniformed technicians who treat your driveway the way they’d treat their own mother’s. Compton residents also get the standing offers every Ironworks customer gets: $50 off any repair over $250, a free second opinion on any written estimate, an $89 seasonal tune-up, and a permanent 5% senior and veteran discount.
Our Gate Installation Services in Compton
Driveway Gate
A driveway gate in Compton is rarely a decorative choice. It’s perimeter security, and it needs to close every time. We install sliding and swing driveway gates sized to your opening, set posts in concrete footings poured below the crack line, and hang the panel so it clears the heave that’s already in your driveway slab. If you’re replacing a gate that’s been on the property since the Nixon administration, we’ll remove and haul the old steel too.
Pedestrian Gate
Pedestrian gates on Compton lots take abuse. Kids, deliveries, gardeners, the postal carrier. The hinges wear first, then the latch post leans. We install new pedestrian gates with hot-dipped galvanized posts, adjustable hinges, and closers that don’t slam. When we set a pedestrian gate next to a driveway gate, we match the steel profile and powder coat so the whole frontage reads as one line.
Sliding Gate
Sliding gates are the workhorse of Compton’s residential parcels. But a sliding gate is only as good as its track. On 1950s and 1960s driveways, the slab at the track line is often cracked or pitched from roots, which means the gate starts binding, the wheels wear unevenly, and the operator strains until the thermal overload trips. Before we hang a new sliding gate, we check the track bed, grind or re-level where we can, and anchor new track with wedge bolts into solid concrete. If the old slab is beyond saving, we’ll tell you before we quote, not after we start.
Swing Gate
Swing gates are where Compton’s Santa Ana winds do their work. A dual-swing driveway gate catches the wind like a sail, and if the hinges were undersized or the posts were set shallow, it’s only a matter of time. We install swing gates with reinforced hinge plates, posts set in 24-inch footings with rebar cages, and manual or automatic closers. For anything that will carry an operator, we spec the hinges before we order the steel, because retrofitting hinges after the gate is hung is twice the labor.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Trusted Brands We Service in Compton
We train on nine gate automation brands, and in Compton we see a lot of LiftMaster, FAAC, BFT, and Linear on the older residential installs. That matters because control boards age out, safety loops fail, and remotes get lost. We keep Gate Parts & Welding in Compton common parts for these brands on the truck, which means a service call doesn’t turn into a two-week parts wait. If your old operator is a brand we don’t recognize, we’ll still assess it and tell you honestly whether it can be saved or whether a new board and receiver costs less than nursing a thirty-year-old relay box.
Common Gate Installation Problems We See in Compton Homes
- Santa Ana wind damage: Strong fall wind events routinely blow unlatched swing gates off their hinges and bend the frame of unsecured sliding gates. We see a predictable spike in Compton service calls after every major wind event, and we re-square gates and replace hinge posts before installing any new operator.
- Heaved and cracked driveway slabs: Mature tree roots and fifty-plus years of soil movement mean the concrete under a sliding gate track is rarely flat. If a new track is bolted to a pitched slab, the gate binds within months. We re-level or replace the track bed before the gate goes on.
- Pre-UL 325 gates with no safety provisions: Many Compton gates were hung before entrapment safety rules existed. There’s no room for photo-eye brackets, no edge sensor rail, and no way to meet current code without modifying the posts or replacing the gate. We’ll show you exactly what’s missing and quote the retrofit honestly.
- Aging wrought-iron and tubular steel: The dry inland air accelerates surface rust on bare steel and older wrought iron. Hinges seize, welds crack at stress points, and the gate’s bottom rail rusts through where sprinkler overspray hits it. We cut out rotted sections and weld in new steel, or replace the panel when the rust has gone structural.
Pricing for Gate Installation in Compton, CA
In Compton’s market, a new pedestrian gate typically runs $900 to $1,800 installed depending on steel profile, width, and powder coat. A single swing driveway gate usually falls between $1,800 and $3,500 for the gate and post work, with automation adding $1,200 to $2,800 depending on the operator and safety equipment. A sliding driveway gate on a new track runs $2,500 to $5,000, with the track bed work separate if the slab needs re-pouring. A double gate adds roughly 40% to the single panel price. Every price is quoted and agreed in writing before any work starts. You will not see a larger number on the invoice than the one you approved. Call (747) 774-7784 and we’ll come measure the opening, check the existing posts and slab, and hand you a written number.
We Also Serve Cities Near Compton
While this page is about Gate Installation in Compton, our crews also work the surrounding streets in Lynwood, Paramount, South Gate, and Huntington Park. If you’re on the edge of Compton and your address sits in a neighboring city, the same team covers it with the same pricing and the same written guarantee.
Serving Compton, CA - Our Local Coverage Area
We’re based in the Compton area and know this community well, providing Compton Gate Access Control. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs - Gate Installation in Compton
You can retrofit most 1960s-era swing gates, but it depends on the gate’s weight, the hinge condition, and whether the posts meet the mounting requirements for a modern operator. The real question is whether the gate was hung before UL 325 entrapment safety rules. If there’s no room for a photo eye bracket or an edge sensor, you’ll need to modify or replace the gate to be code-compliant. We assess this in person, for free, and tell you the honest cost of retrofit versus replacement. Call (747) 774-7784 to schedule a look.
The driveway slabs under Compton’s sliding gate tracks have been moving for fifty to seventy years, usually from tree roots and soil settlement. A track bolted to a pitched slab will cause the gate to bind, the rollers to wear unevenly, and the operator to work against the load until it trips or burns out. Re-leveling means grinding down high spots, shimming low sections, or replacing a rotted section of slab so the track sits true before the operator goes on. It’s faster and cheaper to do it before the install than to tear out a burned operator a year later. (747) 774-7784 gets you a free assessment.
If the operator is throwing the chain repeatedly, the problem is usually not the chain itself, it’s the track or the rollers underneath. Constant truck traffic along the Alameda Street freight corridor vibrates the embedded steel track loose, which pulls the gate out of line, which overloads the chain drive. You can replace the chain, but it’ll throw again until the track is re-leveled and the rollers are replaced. Sometimes a rack and pinion conversion is the cheaper long-term answer because it eliminates the chain failure point entirely. We service commercial and residential gates in Compton and can tell you which fix makes sense for your yard. Call (747) 774-7784 for a free estimate on the repair.
The post moved. Not the gate, the post. Compton’s older concrete work rarely provides a stable footing for a swing gate post, especially when roots have been pushing against the footing for decades. If the post is set too shallow or into cracked concrete, the gate’s weight and the wind load from Santa Ana events will slowly push it out of plumb, and the gate will sag and bind at the latch. We set swing gate posts in 24-inch footings with rebar cages, below the crack line, so the post stays where we put it. If your gate is already sagging, call (747) 774-7784 and we’ll tell you if the post can be re-anchored or needs a new footing.
A standard AC operator works fine on most Compton driveways, as long as there’s a circuit within reach of the gate location. Compton’s pre-1970 homes often lack an outdoor outlet near the gate, which means running conduit across the yard or tapping a circuit from the garage. A solar operator avoids that trenching and is a good fit for a single swing gate that opens a few times a day. But solar doesn’t perform as well on a dark lot or a heavily used commercial gate. We’ll look at your electrical situation, your gate’s duty cycle, and the sun exposure on your property before recommending one or the other. Call (747) 774-7784 for a free site visit.
On a 1958 street off Rosecrans Avenue, we replaced a sagging wrought-iron swing gate where the hinge post had rotted at the footing and the old operator was a pre-UL 325 model with no safety photocell. After pouring a new post footing and re-hanging the panel with a modern LiftMaster operator, loop detector, and edge sensors, we re-squared the gate so the latch no longer bound. Then we recommended a rack and pinion retrofit for the adjacent slide gate, which would cost less than repeatedly repairing its worn chain drive. That’s the kind of job we do in Compton every week, and it’s why we lead with the footing and the track before we talk about the gate itself.
If you’re ready for a gate that closes right and stays square through the wind, the heat, and the roots, call Ironworks Gate Co. at (747) 774-7784. We’ll come out, look at your existing setup, and hand you a written price before any work starts. A square deal: upfront price, no surprises on the bill.
Written by Victor Salinas, Owner at Ironworks Gate Co., serving Compton with square-deal gate installation and repair since 1984.