Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFast, Reliable Gate Parts & Welding Across Maywood
Gate hinge replacement in Maywood typically runs $225-$450 per hinge post, and most welding repairs are completed the same day we arrive. If your swing gate scrapes the sidewalk on Atlantic Boulevard or the hinges have pulled loose from a 1930s brick pillar, we can weld it right and have it closing square again. Ironworks Gate Co. has been welding and rebuilding gates for over 42 years, and we know Maywood’s tight lots and old masonry better than any generalist crew. Call (747) 774-7784 for a free estimate, quoted before any work starts.
When you need Gate Parts & Welding in Maywood, the job is rarely about the gate alone. It’s about the pillar, the post, the sidewalk clearance, and the way a 70-year-old house sits six feet from the street. We work all of Maywood from the flats near Slauson Avenue up to the homes around Maywood Avenue and East 56th Street, and we bring the right steel, the right welder, and the right crew to every call.
Why Ironworks Gate Co. Is Maywood’s Preferred Gate Parts & Welding Company
Maywood is one of the densest cities in California, and nearly every home here has a security gate of some kind. Most of those gates are original wrought iron from the 1920s through the 1950s, and most of them are hung on posts set into brick or stucco pillars that were never built to last this long. That’s the work we do every week in Maywood: cutting out rusted hinge posts, welding new steel into place, and rebuilding hardware so the gate clears the sidewalk and swings true.
We are not a general handyman service. Ironworks Gate Co. works exclusively on driveway and estate gates, and our crew has been welding and fitting gate hardware since 1984. When a Maywood homeowner calls, they talk to a real person, not a voicemail tree, and they get a technician who has seen this exact failure a hundred times before. Our work comes with a written 90-Day Done Right Promise. If it is not right, we come back and make it right. No arguing, no paperwork, no exceptions.
We also know the code issues that come with Maywood’s lot dimensions. Most front setbacks here are under 15 feet, and a swing gate that arcs out over the public sidewalk is a citation waiting to happen. We set hinge geometry and post placement so your gate stays on your property, every time.
Our Gate Parts & Welding Services in Maywood
Hinge Replacement
Maywood’s original swing gates hang on hinges set into brick pillars that predate World War II. The hinge plates rust, the screws strip out of old mortar, and the gate begins to drop until it drags on the walkway. We replace the hinge with a heavier plate, weld a new barrel assembly if needed, and reset the gate so it clears the sidewalk by a measured margin. Hinge replacement in Maywood typically runs $180-$320 per hinge, including realignment of the gate leaf.
Post Replacement
When the hinge post inside a brick or stucco pillar has rusted through, patching it is a waste of your money. We cut the old post flush, weld in a new 4-inch square steel post, and set it into a fresh concrete footing inside the existing pillar. This is the most common repair we do in Maywood, because the original posts in 1920s and 1930s pillars were rarely painted on the buried side. Post replacement typically runs $400-$750 per post, depending on pillar condition and whether we need to open the masonry at all.
Rail Repair
The bottom rail of a Maywood wrought iron gate takes more abuse than any other part. Rain runs down the pickets and sits on the rail, the paint wears thin, and the rail rusts through at the corners. We can cut out a rusted section and weld in a matched replacement, or rebuild the entire rail if the corrosion has spread. Rail repair runs $150-$350 for a section, or $500-$900 for a full bottom rail replacement on a double gate.
Custom Welding
Some Maywood homeowners want to keep their original gate, even when the bottom rail is gone and two pickets are snapped. That is when we custom-fabricate the repair. We match the square bar and picket spacing of 1940s and 1950s wrought iron, weld the new sections in, and grind the joints so the repair disappears into the original work. Custom welding in Maywood runs $125-$250 per hour, and most jobs take two to four hours.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Trusted Brands We Service in Maywood
Maywood homeowners have gates with all kinds of hardware on them, and our welding shop works with all of it. We carry parts and maintain certification on Linear, Viking, and DoorKing automation systems, which means we can weld new hinge plates onto a gate and then set the operator travel limits to match the new geometry the same day. You do not need to call one company for the metal and another for the motor. We handle the full job from the welder to the remote control.
Common Gate Parts & Welding Problems We See in Maywood Homes
- Hinge posts rusted out inside the pillar. The original 1920s-1940s gate posts in Maywood were set directly into brick pillars with no drainage, and the buried section rusts until the gate drops and drags on the walk. We cut and weld new post stubs without demoing the pillar.
- Fatigue cracks at the welded hinge plates. Short-throw swing gates cycle more times per day than a long driveway gate ever will, and decades of that work hardens the metal at the weld until it cracks. We weld a gusset plate behind the hinge to carry the load for another forty years.
- Bottom rollers bent or broken on converted slide gates. When a Maywood driveway is too shallow for a swing gate, the gate gets converted to slide, and the rollers take abuse from cars cutting the turn tight. We weld new roller brackets and replace the carrier wheels, then set the guide so the gate tracks straight.
- Gate scrapes the sidewalk after years of sag. The hinge side of the gate settles, the latch side drags, and eventually the gate leaves a score mark across the public walk. We correct the geometry with welded hinge shims or post realignment, then check clearance at the lowest point of the arc.
Pricing for Gate Parts & Welding in Maywood, CA
Gate parts and welding in Maywood is priced by the repair, not by the hour on most jobs, so you know the number before we strike an arc. Hinge replacement runs $180-$320 per hinge. A post replacement runs $400-$750 per post. Rail repair runs $150-$350 for a section, and a full bottom rail rebuild runs $500-$900. Custom welding is $125-$250 per hour when the job does not fit a flat rate. What changes the price most in Maywood is the condition of the original pillar: a solid 1930s brick pillar usually lets us weld in a new post without any masonry work, while a crumbling stucco pillar may need an extra hour of prep. Every estimate is free, and the price is agreed in writing before work begins. Call (747) 774-7784 for an exact quote.
We Also Serve Cities Near Maywood
Our gate parts and welding crews cover Maywood and the surrounding communities, including Huntington Park, Bell Gardens, South Gate, and Lynwood. If you are just outside Maywood, call (747) 774-7784 and we will tell you when we can be there.
Serving Maywood, CA - Our Local Coverage Area
We’re based in the Maywood area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs - Gate Parts & Welding in Maywood
Because the post inside the pillar has settled or the pillar itself has shifted, so the hinge leaf no longer holds the gate at the correct height. In Maywood, where most gates sit less than 15 feet from the public walk, even half an inch of post settlement puts the gate onto the sidewalk. We correct it by welding shims behind the hinge plate or resetting the post in fresh footing, then checking the low point of the arc with a level. Call (747) 774-7784 and we will measure it for free.
Yes, in most cases. We cut the old post flush at the top of the pillar cap, remove the rusted stub with a core drill if needed, and weld the new post into place with a bracket that locks into the pillar’s interior void. The brickwork stays intact. We only open the pillar when the brick around the post is unsound, which we assess on site. Every price is quoted before we start, so there are no surprises.
Most cracked hinge welds on Maywood’s original wrought iron gates can be repaired by grinding out the crack, re-welding the joint, and adding a gusset plate behind the hinge to spread the load. Replacement is only necessary when the hinge plate itself is deformed or the surrounding metal is thin from years of corrosion. Call (747) 774-7784 for a free assessment, and we will tell you honestly which route makes sense.
Yes. On Maywood lots with less than 15 feet of front setback, a swing gate often cannot open without crossing the public sidewalk, and that is a citation. We convert the opening to a slide gate with a welded steel frame, new roller carriers, and a bottom track or cantilever rail, depending on the driveway width. Most slide gate installs in Maywood run $2,800-$5,500 including the steel, hardware, and welding. Call for a free measure and a written price.
The welded hardware and the operator have to be set up together, or the gate will bind and the motor will burn out. When we weld new hinges, posts, or rollers in Maywood, we check the operator’s travel limits, force settings, and closing speed so the gate opens and closes without straining the motor or the welds. We service and program nine major brands, and we stock parts for Linear, Viking, and DoorKing in our van. Call (747) 774-7784 to schedule a tune-up or a repair with the same crew that knows your gate’s metal.
Call Ironworks Gate Co. for Gate Parts & Welding in Maywood
If your Maywood gate is sagging, scraping, cracking, or rusting through, call (747) 774-7784 for a free estimate. We will come out, look at the pillar and the hinges and the sidewalk clearance, and tell you exactly what the repair will cost, in writing, before any work begins. A live person answers the phone 24 hours a day, 7 days a week. Ironworks Gate Co. has been welding gates since 1984, and we stand behind every job with the 90-Day Done Right Promise. Done right, and backed in writing.
Written by Victor Salinas, Owner at Ironworks Gate Co., serving Maywood and surrounding communities since 1984.